Skillnad mellan versioner av "Airport Procedures"

Från Master Arms Wiki
Hoppa till navigering Hoppa till sök
Rad 119: Rad 119:
 
Use the draw tool and open the json file to display Kutaisi CTA in LotAtc.
 
Use the draw tool and open the json file to display Kutaisi CTA in LotAtc.
  
[[Media:MA_Master_Kutaisi_CTA_220210_Bankler_version.json]]
+
[[Media:MA_Master_Kutaisi_CTA_220210_Bankler_version.json.zip]]

Versionen från 20 februari 2022 kl. 10.39

Home >> Standard Operating Procedures >> Airport Procedures

Though inspired by real life operations, our goal is to strike a balance between realism and manageability. The airspace types listed below are most useful during training events with live ATC in order to increase immersion.

Overview

Overview

The airspace structure is usually viewed as an inverted cake, extending from the airport and up.

Control Area (CTA)

CTA

The CTA represents the top of the cake and covers a large area, it’s purpose is to route and separate traffic to, from and through the region. With live ATC the airspace is controlled. It’s bottom starts at 10 000 feet above mean sea level (MSL) and continues to infinity (marked as UNL). Note that you can fly below the CTA.

Terminal Area (TMA)

TMA

The TMA is the middle portion of the cake and serves more as a facility to route traffic to and from airports. With live ATC the airspace is controlled. It’s bottom starts at 1500 feet MSL and the ceiling stops at 10 000 feet where the CTA starts. Parts of the the TMA can have a floor defined as 1500 feet above ground level (AGL) due to high terrain elevation. Several airports are located under a single TMA. Note that you can fly below the TMA.

Control Zone (CTR)

CTR

The CTR is the top of the inverted cake and covers an airfield. It’s purpose is to protect aircraft departing and arriving at individual airports. With live ATC the airspace is controlled. It reaches from ground level to 1500 feet AGL. Note that you shouldn’t fly below the CTR.

Restricted Area (R)

A restricted area is basically a controlled airspace which is not necessarily close to any airports. They are positioned to protect traffic from live fire. Avoid these unless cleared by ATC or if you are aware of traffic within the airspace.

Departure and arrival

The most common type of departure used is a visual one. Normally ATC will clear you towards an exit point marked on a Visual Operations Chart, you are then expected to navigate visually following the route on the chart. Same goes for arrival.

ATC can also issue specific headings or TACAN radials to follow after take off, in this case the exit points are no longer valid.

Controlled and Uncontrolled Flight

With live ATC all flights are controlled within CTR, TMA and CTA. Players can still fly uncontrolled below TMA and CTA without any clearance, just be aware of your position relative to any airports or restricted areas.

VFR or IFR

Visual Flight Rules (VFR) means that the pilot has navigation responsibility using visual references. Navigation aids such as INS, TACAN or ATC may be used to enhance situational awareness.

Instrument Flight Rules (IFR) can be applied in visual conditions but puts more navigation responsibility on ATC. INS or TACAN etc. may also be used for navigation. IFR flights may be conducted in poor weather.

Speed restrictions

Maintain a maximum speed of 300 KIAS below 10 000 feet unless cleared high speed by ATC. This can always be requested but might be denied due to ATC workload.


Landing Pattern

Overhead Break

The standard landing pattern for arriving traffic is the overhead break. Straight in landings or formation landings must be requested well ahead of arrival to accommodate for increased spacing on final approach. All aircraft from all branches are expected to break at 1500 feet AGL and to maintain that altitude until turning base. The pattern direction is indicated on the Visual Operations Chart.

Go Around / Missed Approach

If the approach is aborted after the break, complete the pattern and position yourself overhead the runway and continue on the runway track. Climb gently to 1000 feet AGL to stay below arriving traffic and increase speed to 300 KIAS. You will then be cleared by tower to break again when the sequence is correct, this includes a climb to 1500 feet AGL.















Kutaisi CTA

Overview

The descriptions above apply to the airspace surrounding the western region of Georgia.

Lanchhuti Transition

Overview

Lanchhuti Transition is a local procedure to deconflict departing and arriving traffic from R99 and Kobuleti CTR while flying to and from Kutaisi airfield. It is a VFR transition.

Departing traffic:

  • After passing assigned exit point, fly towards and then along the ridge southwest of Kutaisi. Pass between Kobuleti CTR and R99.
  • Expect 5000 feet initially and further climb once established along the ridge.

Arriving traffic:

  • Expect 3000 feet initially and 1600 feet once clear of terrain.
  • Report approaching Entry West if you still have not recieved "Cleared approach" or tower channel by that time.













Resources

In Game Kneeboard

Drop the images contained in the file below in your C:\Users\YOURNAME\Saved Games\DCS.openbeta\Kneeboard folder to access section charts of Kutaisi CTA during flight.

Media:MA Kutaisi CTA kneeboard.zip

Tacview Objects

Drop the XML file into C:\Users\YOURNAME\AppData\Roaming\Tacview\Data\Static Objects to display Kutaisi CTA in Tacview.

Media:Kutaisi CTA Tacview.zip

LotAtc Overlay

Use the draw tool and open the json file to display Kutaisi CTA in LotAtc.

Media:MA_Master_Kutaisi_CTA_220210_Bankler_version.json.zip