A-10C Procedures

The following sections describe Tactics, Techniques and Procedures (TTP) that are valid only for A-10C.

Some Tactics and Techniques have reference to the manual "DCS A-10C II Flight Manual EN", this manual can be found in the DCS installation folder "DCS World OpenBeta\Mods\aircraft\A-10C_2\Doc"

Considerations

The A-10Cs provide the ability to maneuver and reposition firepower in response to changing situations. They carry a wide variety of forward firing munitions, are equipped with advanced sensors, have excellent loiter times and have an excellent capability to conduct CAS in diverse terrain and when accompanying other transport or rescue assets.

Consider combining FW (A-10C) and RW (AH-64D) platform capabilities in an urban environment. FW can often target/designate within urban areas more easily due to the ability to loiter high above many threat envelopes. Once the FW aircraft has identified and confirmed the target it can designate the target with a LASER to guide precise, low-yield PGMs fired from a RW attack asset holding in a relatively safe BP.

Operating Range/Altitudes

Service ceiling: 45,000ft Recommended operating altitude: <25,000ft Rate of climb: 6,000 ft/min Combat Range 252 nm Ferry Range 2,240 nm

Capabilities

Tasks:

• Attack (BAI/CAS)
• Reconnaissance
• CSAR
• Aerial C2/AFAC

Tactics and Techniques

Tasks

• Attack (BAI/CAS)
• Reconnaissance

-Zone

-Area

-Route

• CSAR
• Aerial C2/AFAC

En Route

Ideally, en route tactics (route, altitude, airspeed selection and formations) allow aircrews to avoid concentrations of enemy air defenses, prevent early acquisition, avoid detection or allow the aircrews to remain outside of the effective range of certain threat systems.

Tactical Formations

• Finger Four: (Default if not specified)

• Echelon (left/right):

• Trail:

• Combat Spread:

Formations explained here.

Disengagement and Egress

Following actions on the objective area or when the time on station is complete, the flight will conduct a check out and egress via planned or assigned routing. Tactical considerations for the egress and return to force in terms of airspeed, altitude, formation, and TTP are the same as for the inbound en route phase. When complete with the mission, the aircrew will make every attempt to provide BDA and a mission report (MISREP) via the ALO’s C2 system.

Procedures

The procedures described here aim to ensure a common view of the workflow during assignments in order to facilitate the change of staff. Pilots knows who do what and when even if it’s the first time flying together.

Airfield

The order in which the steps not numbered are performed can be changed as needed.

Startup

1. Connect ground power
2. CDU/EGI - ON
3. CICU/JTRS/IFFCC - ON
4. VHF AM - TR (Enter Intra VHF freq. - FL Radio Check)
5. Rearm
6. UHF - Listen to ATIS and take notes.
7. UHF - Select Preset Ch 6. (report done on Intra VHF)
8. FL Radio Check Ch 6
   1. 11
   2. 22

1. Engine Startup (After CPG has received clearance from Ground)

• CMWS Setup
• Set transponder (SRS Overlay)
• Exterior Lights
  • Nav -> BRT and ANTI-COL -> WHT (Day) / RED (Night)
• MENU-Page
  • ASE

- RLWR - ON

• FLT

- QNH

• FUEL

- Auxiliary tanks transfer setup

• PERF (WIP)

- Enter current value for PA, FAT and GWT

• WPN-Page

- Boresight IHADSS

- Set Manual Range (GUN) as desired

• Personal preferred settings

- Phase/Threat Show

- MAP

- BAM

- HI/LO Altitude Warnings

Glossary

STANDARD MARKING BREVITY TERMS

• BLIND No visual contact with FRIENDLY aircraft/ground position.
• VISUAL Sighting of a FRIENDLY aircraft or ground position.
• CONTACT Acknowledges sighting of a specified reference point (either visually or via sensor).
• CAPTURED Specified surface target or object has been acquired and is being tracked with an onboard sensor.
• LOOKING Aircrew does not have the ground object, reference point, or target in sight.
• TALLY Sighting of a target, non-friendly aircraft, or enemy position.
• NO JOY Aircrew does not have visual contact with the TARGET/BANDIT.

LASER BREVITY TERMS

• TEN SECONDS Standby for LASER ON call in approximately 10 seconds
• LASER ON Start/ acknowledge LASER designation
• SHIFT Shift LASER aimpoint.
• SPOT Acquisition of LASER designation
• CEASE LASER Discontinue lasing
• DEAD EYE LASER designator system inoperative
• NEGATIVE LASER LASER energy has not been acquired
• LASING The speaker is firing the LASER
• STARE Cue the LASER spot search/ tracker function on the specified location

Abbreviations

• ACA Airspace Coordination Areas
• ACM Airspace Coordinating Measure/Airspace Control Means
• AGL Above Ground Level
• AGO Air-Ground Operations*
• ALO Air Liaison Officer
• BDA Battle Damage Assessment
• C2 Command and Control
• JFC Joint Force Commander

*The simultaneous or synchronized employment of ground forces with aviation maneuver and fires to seize, retain, and exploit the initiative. Also called AGO.